Panasonic WJMP204 Instrucciones de operaciones descargar pdf (Pagina 14)

OFF by pressing button 3 (–) or button 4 (+).

The initial factory setting is ON.

• Terminal Alarm Setting

1. Display the SYSTEM menu.

2. Move the cursor to TERM. ALARM by pressing button 1

OFF by pressing button 3 (–) or button 4 (+).

The initial factory setting is ON.

• Alarm Output Data (Alarm Output Duration from

Alarm Connector)

1. Display the SYSTEM menu.

2. Move the cursor to ALARM OUTPUT by pressing but-

ton 1 (C) or button 2 (D), then select the desired alarm

output duration, 1S - 30S, 40S, 50S, 1MIN, 2MIN, 3MIN,

4MIN, 5MIN, EXT or OFF, by pressing button 3 (–) or

button 4 (+).

The initial factory setting is 10S. Enable to set by 1 sec-

ond (1S - 30S).

EXT: The alarm signal continues to be output from

ALARM/REMOTE connector till the alarm is reset.

The alarm is not automatically reset.

1S-5MIN: The alarm signal is supplied from ALARM/

REMOTE connector only for the set time. The

alarm is automatically reset after the set time.

(The ALARM indicator changes from blink to

steady light.)

OFF: The alarm signal is not supplied from ALARM/

REMOTE connector. The alarm is not automati-

cally reset.

• Alarm Data

This is to set whether or not the alarm data received

from a camera is to be transmitted to the WV-CU360.

OFF: Select this parameter if the system controller is

not connected to the system, or if operation is

to be controlled via an AV Codec.

0S: Each time an alarm is detected, it is notified to

the system controller.

1S: When an alarm is detected, it is notified to the

system controller. (Alarm data on each channel

where an alarm is detected is stored for 1 sec-

ond, and the stored alarm data is sent to the

system controller.)

5S: When an alarm is detected, it is notified to the

system controller. (Alarm data on each channel

where an alarm is detected is stored for 5 sec-

onds, and the stored alarm data is sent to the

system controller.)

Note: To set 0S, 1S or 5S, the system controller set as

controller No. 1 must be connected to the system.

1. Display the SYSTEM menu.

2. Move the cursor to ALARM DATA by pressing button 1

duration, OFF, 0S, 1S, or 5S, by pressing button 3 (–)

or button 4 (+).

The initial factory setting is 1S.

1. Display the SYSTEM menu.

2. Move the cursor to ALARM MODE by pressing button 1

then select MONITOR SPOT ON or OFF by pressing

button 3 (–) or button 4 (+).

The initial factory setting is ON.

ON: The screen of the corresponding channel appears

when the alarm is activated. If MONITOR SPOT ON

with the mark is selected, the screen appears

as shown below.

MONITOR SPOT

ALARM CAM NO. PRE

1 1CH -

2 2CH -

3 3CH -

4 4CH -

Enter each camera number and a preset position for

each alarm number. If the Data Multiplex Unit is con-

nected to a combination camera, enter a preset posi-

tion for the PRE parameter.

OFF: The screen continues to display the pictures in

the mode selected previously when the alarm is

activated.

For further information on preset positions, refer to the

Operating Instructions for the combination camera.

• Alarm Display Setting

1. Display the SYSTEM menu.

2. Move the cursor to ALARM DISPLAY by pressing button

1 (C) or button 2 (D), then select ALARM DISPLAY ON

or OFF by pressing button 3 (–) or button 4 (+) so that

[ALARM∗∗∗] appears on the screen or not.

The initial factory setting is ON.

Note: The figure shown in the place of [∗∗∗] after the

word ALARM is a channel number.

• Site Alarm Setting

1. Display the SYSTEM menu.

2. Move the cursor to SITE ALARM by pressing button 1

ALARM MODE

MONITOR SPOT ON

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM DATA 1S

(1) Alarm Mode Setting

• Monitor Spot Setting

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 30 31

Comentarios a estos manuales

Sin comentarios

Panasonic WJMP204 Instrucciones de operaciones Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras De Seguridad Panasonic WJMP204