Panasonic WJSX350 Instrucciones de operaciones descargar pdf (Pagina 38)

-36-

A L A R M M O D E 3 ( A L = 0 1 )

M O D E = – – - – –

< < M 1 M 2 M 3 M 4 > >

S S T T

< < M 5 M 6 M 7 M 8 > >

G G G G

A L A R M M O D E 3 ( A L = 0 1 )

M O D E = S P O T C A M = 0 1

P R E = 0 1

M O N I = 2 D W E L L = 1 0 S

< < M 1 M 2 M 3 M 4 > >

S S T T

< < M 5 M 6 M 7 M 8 > >

G G G G

Then press the CAM (SET) button to display the

mode setup table of the selected alarm input as

shown below.

• Mode selection on ALARM MODE3 table

Move the cursor to the MODE parameter by moving the

Joystick Controller. Then set the Mode to SPOT, TOUR

or GROUP by pressing the +1CAM INC or –1CAM DEC

button.

• Spot Mode

1. If the SPOT is selected on the above menu, the dis-

play will change as follows:

2. Move the cursor to the MONI parameter by moving

the Joystick Controller, then enter a Monitor Number

to display the spot picture by pressing the Numeric

button or the +1CAM INC or –1CAM DEC button.

Notes:

• Monitor Numbers without the S cannot be pro-

grammed on this table.

• If a correct Monitor Number is entered, the

selected monitor in the Monitor Number area is

displayed inversely.

• If an incorrect Monitor Number is entered, the

selected monitor in the Monitor Number area

blinks.

3. Move the cursor to the CAM parameter by moving

the Joystick Controller, then enter a Camera

Number by pressing the Numeric buttons or the

+1CAM INC or –1CAM DEC button.

4. Move the cursor to the PRE parameter by moving

the Joystick Controller, then enter a Preset Position

Number, if applicable, by pressing the Numeric but-

tons or the +1CAM INC or –1CAM DEC button.

5. Move the cursor to the DWELL parameter by mov-

ing the Joystick Controller, then enter the desired

Dwell Time(1-30) by pressing the Numeric buttons

or the +1CAM INC or –1CAM DEC button.

6. Press the MON (ESC) button to return to the previ-

ous ALARM MODE 3 menu.

• Tour Sequence Mode

1. If TOUR is selected on the above menu, the display

will change as follows:

A L A R M M O D E 3 ( A L = 0 1 )

M O D E = T O U R

S E Q N O. = 0 1

M O N I = 3

< < M 1 M 2 M 3 M 4 > >

S S T T

< < M 5 M 6 M 7 M 8 > >

G G G G

2. Move the cursor to the MONI parameter by moving

the Joystick Controller, then enter a Monitor Number

(1-8) to run the sequence by pressing the Numeric

button or the +1CAM INC or –1CAM DEC button.

Notes: Select a Monitor Number with T (Tour

Sequence Mode) that is previously assigned to

the Monitor Number area.

Monitor Numbers without the T cannot be pro-

grammed on this table.

3. Move the cursor to the SEQ NO. parameter by mov-

ing the Joystick Controller, then enter a Tour

Sequence Number to be run on the selected moni-

tor by pressing the Numeric button or the +1CAM

INC or –1CAM DEC button.

4. Press the MON (ESC) button to return to the previ-

ous ALARM MODE 3 menu.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 67 68

Comentarios a estos manuales

Sin comentarios

Panasonic WJSX350 Instrucciones de operaciones Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras De Seguridad Panasonic WJSX350