Panasonic SCHTB527 Instrucciones de operaciones descargar pdf (Pagina 21)

Reference

Operations

RQT9834

∫ To reduce the clear-mode dialog effect

When the dialog does not sound natural while the

volume is set low, it is possible to reduce the dialog

enhancing effect as follows:

While pressing and holding [TV] on the remote

control, press and hold [VOLUME s] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



≥ To reset the setting, return to the factory preset. (> right)

∫ To turn off VIERA Link “HDAVI Control”

When “HDAVI Control” compatible equipment does

not work well with this system, for example, it is

possible to turn off this function as follows:

≥ When VIERA Link is turned off, the ARC function is not

available. Be sure to connect the optical digital audio cable.

(> 14)

1 While pressing and holding [MUTE] on the

remote control, press and hold [VOLUME s]

on the main unit for more than 2 sec.

A will blink once when the setting is changed.

2 After the setting has changed, turn off all the

connected devices and then turn them on again.



To reset the setting, return to the factory preset. (> right)

∫ To turn off the volume limitation

If a state of the lowered volume disturbs you every

time the main unit turns on, for example, it is

possible to turn off this function as follows:

While pressing and holding [MUTE] on the remote

control, press and hold [VOLUME i] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



To reset the setting, return to the factory preset. (> right)

Reference

Troubleshooting

Before requesting service, make the following

checks. If you are in doubt about some of the check

points, or if the solutions indicated in the following

guide do not solve the problem, consult your dealer

for instructions.

No power.

≥ Insert the AC mains lead securely. (> 16)

≥ After turning the main unit on, if the indicators

blink and the main unit immediately turns off,

unplug the AC mains lead and consult your

dealer.

The remote control does not work properly.

≥ The battery is depleted. Replace it with a new

one. (> 7)

≥ It is possible that the insulation sheet has not

been removed. Remove the insulation sheet.

(> 7)

≥ It may be necessary to set the code of the remote

control again after changing the battery of the

remote control. (> 20)

≥ Use the remote control within the correct

operation range. (> 7)

The “TV” indicator blinks.

Remove the AC mains lead and consult your

dealer. If there are any other indicators blinking, be

sure to inform your dealer about the blinking

indicators.

TV BD/DVD DTS PCMD

To return to the factory preset.

While the main unit is on, press [Í/I] on the main

unit for more than 4 sec.

(All the indicators will blink twice when this

system is reset.)

If this system does not operate as expected,

returning the settings to the factory preset

may solve the problem.

≥ The remote control code will return to “1” when

this system is returned to the factory preset. To

change the remote control code, refer to page

20.

General operation

SC-HTB527EGEB_RQT9834-B.book 21 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Reference

Operations

RQT9834

∫ To reduce the clear-mode dialog effect

When the dialog does not sound natural while the

volume is set low, it is possible to reduce the dialog

enhancing effect as follows:

While pressing and holding [TV] on the remote

control, press and hold [VOLUME s] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



≥ To reset the setting, return to the factory preset. (> right)

∫ To turn off VIERA Link “HDAVI Control”

When “HDAVI Control” compatible equipment does

not work well with this system, for example, it is

possible to turn off this function as follows:

≥ When VIERA Link is turned off, the ARC function is not

available. Be sure to connect the optical digital audio cable.

(> 14)

1 While pressing and holding [MUTE] on the

remote control, press and hold [VOLUME s]

on the main unit for more than 2 sec.

A will blink once when the setting is changed.

2 After the setting has changed, turn off all the

connected devices and then turn them on again.



To reset the setting, return to the factory preset. (> right)

∫ To turn off the volume limitation

If a state of the lowered volume disturbs you every

time the main unit turns on, for example, it is

possible to turn off this function as follows:

While pressing and holding [MUTE] on the remote

control, press and hold [VOLUME i] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



To reset the setting, return to the factory preset. (> right)

Reference

Troubleshooting

Before requesting service, make the following

checks. If you are in doubt about some of the check

points, or if the solutions indicated in the following

guide do not solve the problem, consult your dealer

for instructions.

No power.

≥ Insert the AC mains lead securely. (> 16)

≥ After turning the main unit on, if the indicators

blink and the main unit immediately turns off,

unplug the AC mains lead and consult your

dealer.

The remote control does not work properly.

≥ The battery is depleted. Replace it with a new

one. (> 7)

≥ It is possible that the insulation sheet has not

been removed. Remove the insulation sheet.

(> 7)

≥ It may be necessary to set the code of the remote

control again after changing the battery of the

remote control. (> 20)

≥ Use the remote control within the correct

operation range. (> 7)

The “TV” indicator blinks.

Remove the AC mains lead and consult your

dealer. If there are any other indicators blinking, be

sure to inform your dealer about the blinking

indicators.

TV BD/DVD DTS PCMD

To return to the factory preset.

While the main unit is on, press [Í/I] on the main

unit for more than 4 sec.

(All the indicators will blink twice when this

system is reset.)

If this system does not operate as expected,

returning the settings to the factory preset

may solve the problem.

≥ The remote control code will return to “1” when

this system is returned to the factory preset. To

change the remote control code, refer to page

20.

General operation

SC-HTB527EGEB_RQT9834-B.book 21 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

Reference

Operations

RQT9834

∫ To reduce the clear-mode dialog effect

When the dialog does not sound natural while the

volume is set low, it is possible to reduce the dialog

enhancing effect as follows:

While pressing and holding [TV] on the remote

control, press and hold [VOLUME s] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



≥ To reset the setting, return to the factory preset. (> right)

∫ To turn off VIERA Link “HDAVI Control”

When “HDAVI Control” compatible equipment does

not work well with this system, for example, it is

possible to turn off this function as follows:

≥ When VIERA Link is turned off, the ARC function is not

available. Be sure to connect the optical digital audio cable.

(> 14)

1 While pressing and holding [MUTE] on the

remote control, press and hold [VOLUME s]

on the main unit for more than 2 sec.

A will blink once when the setting is changed.

2 After the setting has changed, turn off all the

connected devices and then turn them on again.



To reset the setting, return to the factory preset. (> right)

∫ To turn off the volume limitation

If a state of the lowered volume disturbs you every

time the main unit turns on, for example, it is

possible to turn off this function as follows:

While pressing and holding [MUTE] on the remote

control, press and hold [VOLUME i] on the main

unit for more than 2 sec.

A will blink once when the setting is changed.



To reset the setting, return to the factory preset. (> right)

Reference

Troubleshooting

Before requesting service, make the following

checks. If you are in doubt about some of the check

points, or if the solutions indicated in the following

guide do not solve the problem, consult your dealer

for instructions.

No power.

≥ Insert the AC mains lead securely. (> 16)

≥ After turning the main unit on, if the indicators

blink and the main unit immediately turns off,

unplug the AC mains lead and consult your

dealer.

The remote control does not work properly.

≥ The battery is depleted. Replace it with a new

one. (> 7)

≥ It is possible that the insulation sheet has not

been removed. Remove the insulation sheet.

(> 7)

≥ It may be necessary to set the code of the remote

control again after changing the battery of the

remote control. (> 20)

≥ Use the remote control within the correct

operation range. (> 7)

The “TV” indicator blinks.

Remove the AC mains lead and consult your

dealer. If there are any other indicators blinking, be

sure to inform your dealer about the blinking

indicators.

TV BD/DVD DTS PCMD

To return to the factory preset.

While the main unit is on, press [Í/I] on the main

unit for more than 4 sec.

(All the indicators will blink twice when this

system is reset.)

If this system does not operate as expected,

returning the settings to the factory preset

may solve the problem.

≥ The remote control code will return to “1” when

this system is returned to the factory preset. To

change the remote control code, refer to page

20.

General operation

SC-HTB527EGEB_RQT9834-B.book 21 ページ２０１２年１２月１０日　月曜日　午前１１時２９分

RQT9834

Da biste ponovno postavili postavku, vratite je na tvorničke

vrijednosti. (→ desno)

Rješavanje problema

Prije pozivanja servisa obavite sljedeće provjere.

Ako niste sigurni u neka rješenja koja su ovdje

navedena ili ako ona ne pomažu u uklanjanju

problema, obratite se prodavaču.

Vraćanje na tvorničke postavke.

Dok je glavna jedinica uključena, pritišćite [ /I]

na glavnoj jedinici dulje od 4 sekunde.

(Svi će pokazatelji zatreperiti dvaput kada se

ponovno postavi ovaj sustav.)

Ako sustav ne bude radio na očekivani

način, vraćanje na tvorničke postavke moglo

bi riješiti problem.

• Kod daljinskog upravljača vraća se na

"1" nakon što sustav vratite na tvorničke

postavke. Upute o promjeni koda daljinskog

upravljača potražite na 20. str.

Općeniti rad

Nema napajanja.

• Čvrsto umetnite kabel za napajanje izmjeničnom

strujom. (→ 16)

• Ako pokazatelji trepere, a glavna jedinica se

odmah isključi nakon što je uključite, iskopčajte

kabel za napajanje izmjeničnom strujom i

obratite se prodavaču.

Daljinski upravljač ne radi ispravno.

• Baterija je ispražnjena. Zamijenite je novom.

(→ 7)

• Moguće je da traka za izolaciju nije pravilno

uklonjena. Uklonite traku za izolaciju. (→ 7)

• Možda ćete trebati ponovo postaviti kod

daljinskog upravljača nakon što promijenite

baterije daljinskog upravljača. (→ 20)

• Daljinski upravljač mora se koristiti u ispravnom

dometu. (→ 7)

Pokazatelj "TV" treperi.

Odspojite kabel za napajanje izmjeničnom

strujom i obratite se prodavaču. Ako trepere drugi

pokazatelji, obavijestite o tome prodavača.

■

Smanjenje efekta čistih glasova

Kada dijalozi ne zvuče prirodno dok je glasnoća

postavljena na nisku vrijednost, moguće je smanjiti

efekt pojačavanja zvuka dijaloga na sljedeći način:

Dok pritišćete i držite [TV] na daljinskom

upravljaču, pritisnite i držite [VOLUME —] na

glavnoj jedinici dulje od 2 sekunde.

će zatreperiti jednom kada promijenite postavku.

• Da biste ponovno postavili postavku, vratite je na

tvorničke vrijednosti. (→ desno)

■

Isključivanje funkcije VIERA Link

"HDAVI Control"

Kada uređaji kompatibilni s funkcijom “HDAVI

Control” ne rade ispravno sa sustavom, funkcija se

može isključiti na sljedeći način:

• Kada je funkcija VIERA Link isključena, funkcija

ARC nije dostupna. Obavezno spojite optički digitalni

audiokabel. (→ 14)

1 Dok pritišćete i držite [MUTE] (Bez zvuka) na

daljinskom upravljaču, pritisnite i držite [VOLUME

—] na glavnoj jedinici dulje od 2 sekunde.

će zatreperiti jednom kada promijenite postavku.

2 Nakon što se postavka promijeni, isključite

sve spojene uređaje i ponovno ih uključite.

Da biste ponovno postavili postavku, vratite je na tvorničke

vrijednosti. (→ desno)

■

Isključivanje ograničenja glasnoće

Ako vam, primjerice, smeta smanjena glasnoća

svaki put kada uključite glavnu jedinicu, možete tu

funkciju isključiti na sljedeći način:

Dok pritišćete i držite [MUTE] (Bez zvuka) na

daljinskom upravljaču, pritisnite i držite [VOLUME

+] na glavnoj jedinici dulje od 2 sekunde.

će zatreperiti jednom kada promijenite postavku.

FunkcijeNapomene

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 27 28

Comentarios a estos manuales

Sin comentarios

Panasonic SCHTB527 Instrucciones de operaciones Pagina 21

Comentarios a estos manuales

Relacionado con productos y manuales para Juegos de altavoces Panasonic SCHTB527