Panasonic WVBL730_SERIES Instrucciones de operaciones

CCTV CamerasWV-BL730/WV-BL734(Lens : option)Before attempting to connect or operate this product,please read these instructions completely.

!3 Video Output Connector (VIDEO OUT)This connector is used to connect with the VIDEOIN connector of the monitor.!4 Power Cord SocketThis socket is us

Copper wire #24 #22 #20 #18size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)Resistance 0.078 0.050 0.030 0.018Ω/mResistance 0.026 0.017 0.010 0.006Ω/

2. 24 V AC Power SupplyConnect the power cable to the AC/DC compatibleinput terminal on the rear panel of the camera.Copper wire #24 #22 #20 #18size (

-10-Type of RG-59/U RG-6/U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)Recommended (m) 250 500 600 800maximumcable length (ft) 825 1,

-11-Installation of Auto Iris Lens ConnectorInstall the lens connector (YFE4191J100) when using avideo drive ALC lens.The installation should be made

Caution for Mounting the LensThe lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450g(0.99 lbs). If the l

The following adjustment should be made by qualifiedservice personnel or system installers.1. Loosen the screws on the back-focal adjustingring.2. Tur

• Mounting from the bottomThis camera is designed to be mounted from thebottom, as shown below. The mounting hole is astandard photographic pan-head s

-15-1. CAMERA SETUP MENUThis camera utilizes a user setup menu that is displayed on-screen.The setup menu contains various items that form a tree-type

-16-MotionDetectorON/OFFLens DriveSignalSelectionDC VideoSpecialmenuDetectionLevelAdjustmentDetectionMasking AreaSelectionUpsidedownAPGainPede

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.

-17-Left ButtonSet SwitchRight ButtonDown ButtonUp ButtonUp Button (): This button is used to move thecursor upwards. Use this button toselect an item

** CAM SET UP **CAMERA ID OFF ALC/ELC ALC SHUTTER OFFAGC ONSENS UP OFFSYNC INTMOTION DET OFF LENS DRI

-19-• Editing the SPECIAL menuTo edit the SPECIAL menu (change settings), proceedas for editing the CAM SET UP menu above.Move the cursor to END after

-20-1. Camera Identification (CAMERA ID)SettingYou can use the camera identification (CAMERA ID) toassign a name to the camera. The camera ID consists

-21-2. Move the pointer to the character to be edited bypressing or . Then move the cursor to thecharacter area and select a new character.3. Press

1. Move the cursor to the ALC/ELC parameter.2. Select ALC or ELC.Cautions: 1. Under bright lighting conditions such as outdoors,use an ALC type lens b

-23- ** ALC CONT ** BACK LIGHT COMPPRESET OFFMASK SET LEVEL ...I... - +RET END↵ ** ALC CONT ** BACK LIGHT

-24-Blinking2. Move the cursor to MASK SET and press .The 48 mask areas appear on the monitor screen.The cursor is blinking in the top left corner of

-25-3. Shutter Speed Setting (SHUTTER)Note: If ECC is selected, this item is not available.You can select an electronic shutter speed of 1/50(OFF), 1/

-26-4. Gain Control Setting (AGC ON/OFF)You can set the gain (brightness level portion of animage) to automatic level adjustment (ON) or fixedlevel(OF

-27-Important Notices:1. The priority for the sync modes is as follows.1. Multiplexed Vertical Drive (VD2) (Highest pri-ority)2. Line-lock (LL)3. B/W

-28-4. After confirming the cursor is on EXT (VS), press. The phase adjustment menu appears on themonitor.6-1. VS Gen-lock Mode (EXT(VS))1. Move the c

-29-2. After confirming the cursor is on LL, press .The vertical phase adjustment menu appears onthe monitor.3. Move the cursor to COARSE. The cursor

-30-• To reset COARSE and FINE to the values pre-set at the factory, press or simultane-ously. COARSE and FINE adjustments arepreset at the factory

-31-1. Move the cursor to the LENS DRIVE parameter.2. Select DC if you are using the auto iris lens thatrequires a DC drive signal.Select VIDEO if you

-32-9. Special Menu (SPECIAL)This menu lets you adjust and set up the video signalof the camera to meet your requirements.Move the cursor to END on th

-33-When the camera is aimed at a bright light, such as aspotlight, or a surface that reflects bright light, smearor blooming may appear. Therefore,

Pick-up Device: 771 (H) x 582 (V) pixels, Frame Interline Transfer CCDScanning Area: 6.4 (H) x 4.8 (V) mm (Equivalent to scanning area of 1/2” pick-up

-35-Power Source and WV-BL730: 220-240V AC 50 Hz, 4.8WPower Consumption: WV-BL734: 24V AC 50 Hz, 4.8W12V DC, 500 mADimensions (without lens): 67 (W) x

Matsushita Electric Industrial Co., Ltd.Central P.O. Box 288, Osaka 530-91, JapanN1297-0 YWV8QA4827AN Printed in JapanN 30 Gedruckt in JapanImprimé au

-1-ENGLISHTHIS APPARATUS MUST BE EARTHED.To ensure safe operation the three-pin plug supplied must be insertedonly into a standard three-pin power poi

-2-CONTENTSPREFACE ...

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Back Light Compensation (Auto: Factory pre-set,

1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screwsor covers.There are no user serviceable parts inside. Ask a

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS-5-Hi-Z G/L 75ΩVIDEO OUTPOWER220-240V AC 50HzGEN-LOCKALARM OUTGNDVIDEO OUTPOWERGEN-LOCKALARM OUTGNDAC 2

q Auto Iris Lens ConnectorThis connector is used to connect with the auto irislens by a 4-pin male connector that is supplied asa standard accessory (