Panasonic KX-P1121E Manual de usuario

Model No. KX-P1121EOperating InstructionsPlease carefully read this manual, and keep this documentation in a safe place for future reference.Impac

Safety Information (ForUnited Kingdom only)This appliance is supplied with a moulded three pinmains plug for your safety and convenience.A 5 amp fuse

PrecautionsInstallation• Do not place the unit in direct sunlight and near hotequipment.• The unit should not be exposed to extremely highor low tempe

UnpackingHaving unpacked the printer, make sure none of thecontents shown below is missing or damaged.Report damage or shortages to the store from whi

Parts of the PrinterFront View123456ABCDEFGPaper support (Page 23)Top coverPaper feed selector• " " (Friction) Single sheets and envelopes•

Rear ViewABCDEFTractorsPower switch (Page 17)Platen knob (Page 12)Power cord (Page 17)Serial No. LabelNameplate14 Operating InstructionsBefore You Sta

Control PanelABCDEFGHFONT switchPressing this switch will select the character fonts. (Page 31)ON LINE indicatorThis indicator is lit when the printer

Installing the SoftwareSystem RequirementsComputer IBM PC/AT® or compatible machinewith a CD-ROM driveOperatingSystemWindows 2000 / Windows XP /Window

Connecting to aComputerBefore you connect the printer for the first time,install the USB and Printer driver on to yourcomputer. For more information s

Installing the RibbonCassetteMounting the Ribbon Cassette1. A Turn the power on.The carriage will move to the ribbon exchange area(A) automatically.No

4. A Slip the ribbon (A) between the ribbon mask(B) and the printhead nose (C).ABCAB Press down on rear of the ribbon cassetteuntil the wing tab (A) s

IntroductionThank you for purchasing the Panasonic KX-P1121E Impact Dot Matrix Printer.This printer is a versatile, high quality 24-pin dot matrix pri

Removing the Ribbon Cassette1. A Turn the power on.The carriage will move to the ribbon exchange area(A) automatically.B Open the smoked plastic cover

2. Set the paper feed selector (A) to the " "position.A3. Lift off the top cover (A).A4. A Unlock the tractors by pulling the tractorclampin

6. Place the paper with the printed side face downand align the paper sprocket holes with thetractor pins, then close the tractor covers.Make sure the

Single Sheets and Envelopes(Friction Mode)1. A Turn the power on.The PAPER OUT indicator will flash indicating thatno paper is installed in the printe

6. Press LOAD/PARK.The paper will be loaded to the first print line.7. If the ON LINE indicator (A) is not lit, pressON LINE to get ready to print.ASe

Control Panel SoftwareProgramThis software is used to change the configuration of theprinter. Using this software, you can also print out theprinter&a

About the buttonsSend SettingsSends the settings to the printer.Restore DefaultReturns the settings to default.After pressing this button, the screen

Using the Control PanelThe Control Panel allows you to set only Auto LF,Graphic Direction, Page Length, Emulation andDownload buffer.If there is any p

Control PanelABCA FONT indicatorB FONT indicatorC ON LINE indicatorITEMFONT indicatorA BPrint current InitialSetup conditionEmulationAuto LFDownload b

Resetting All Current Settings to theFactory SettingsFollow the instructions below:1. Turn the power on while pressingLOAD/PARK.Make sure that both FO

AbbreviationsWindows® refers to the Microsoft® Windows® operating system.Windows® 2000 refers to the Microsoft® Windows® 2000 operating system.Windows

Printing Out the Current SettingsFollow the instructions below to get a print out of thecurrent settings.1. Load a sheet of paper, and turn the power

Selecting a Character FontYou can select any one of the character fonts bypressing the FONT switch on the Control Panel.The combination of FONT indica

Periodic MaintenanceThe printer does not require any routine maintenance. However, reasonable care of the printer will extend itslife. The following p

TroubleshootingMost problems associated with the printer can be traced to improper setup, installation, or cabling.The following table will assist the

Symptom Possible Cause Probable SolutionPrintout is double-spaced. Auto LF is ON. Set Auto LF to OFF.(Page 27)Keeps printing on the same line. Compute

Printer SpecificationsPower requirements:Refer to the nameplate located on the rear of the printer.Frequency:Current:Interface: USB 2.0 Full speed, Ce

Printing direction: Text printing: Bi-DirectionalBit Image printing: Uni-Directional & Bi-DirectionalLine feed time: Approx. 100 ms[with 4.2 mm (1

Paper SpecificationsPaper which may be used with this unit must be within the specifications provided below.Fanfold PaperWidth: 102–254 mm (4–10 in.)Q

Printing AreaFanfold Paper1st characterPaper perforationsPrinting areaPrinting areaADBACFanfold PaperA 25.4 mm (1 in.)B 17.8 mm (0.7 in.)C 8.38 mm (0.

Single Sheets and EnvelopesBDC1st characterPrinting areaSingle Sheets and EnvelopesB 38 mm (1.5 in.)C 8.38 mm (0.33 in.)D 25.4 mm (1 in.)B. Value B in

Federal Communications Commission Requirements (For United Statesonly)NoteThis equipment has been tested and found to comply with the limits for a Cla

SuppliesModel Number DescriptionKX-P145 Ribbon Cassette (black)Note• To purchase Ribbon Cassette, please contact your dealer.40 Operating Instructions

IndexAAlternate Graphic Mode (A.G.M) 25Auto CR 25Auto LF 25, 27, 34Auto load 25Auto Online 25BBi-directional Printing 36Bold PS 3

RRe-inking Ribbon Cassette 32Ribbon cassette 18, 32SSelf Test 24Single sheet 23, 37, 39Smoked plastic cover 13Specifications 35TTear

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)This symbol on the products and/or accompanying d

Table of ContentsSafety Information ...7For Your Safety ...

Printing Area ...38Supplies ...

For Your SafetyTo prevent severe injury and loss of life, read thissection carefully before using the unit to ensure properand safe operation of your

Plug the power cord firmly into an ACoutlet. Otherwise, it can cause fire orelectric shock.Do not pull, bend, rest objects on, orchafe the power cord

CAUTIONPowerWhen the unit is not used over anextended period of time, switch it off, andunplug it. If an unused unit is leftconnected to a power sourc