Panasonic TXL42D25L Instrucciones de operaciones Pagina 93

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 96
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 92
Maintenance
Frequently Asked Questions
FAQs, etc.
93
Problem Actions
Network
Cannot connect to the network
Check the LAN cable or Wireless LAN Adaptor is connected properly. (p. 67)
Check the connections and settings. (p. 67 - 71)
Check the network equipment and network environment.
The router may not be set to issue IP address automatically. If the network
administrator prefers to allocate an IP address, set an IP address manually. (p. 69)
The router may be using MAC address filtering (security setting). Confirm
the MAC Address of this TV (p. 68) and set the router to be able to use it.
If the problem persists, consult your Internet Service Provider or
telecommunications company.
Cannot select the file during
DLNA operations
Is media server of the connected equipment prepared? (p. 66)
Check applicable data format. (p. 66)
Cannot operate VIERA CAST
Check the connections and settings. (p. 67 - 71)
The server or connected line might be busy now.
Other
The TV does not switch On
Check the mains lead is plugged into the socket outlet.
The TV goes into
“Standby mode”
Off Timer function is activated.
The TV enters “Standby mode” about 30 mins. after analogue
broadcasting ends.
The remote control does not work
or is intermittent
Are the batteries installed correctly? (p. 8)
Has the TV been switched On?
The batteries may be running low. Replace them.
Point the remote control directly at the front of the TV (within about
7 m and a 30 degree angle of the front of the TV).
Situate the TV away from sunshine or other sources of bright light
not to shine on the TV’s remote control signal receiver.
Parts of the TV become hot
Even when the temperature of parts of the front, top and rear
panels has risen, these temperature rises will not pose any
problems in terms of performance or quality.
The LCD panel moves slightly
when it is pushed with a finger
Clattered sound might be heard
There is some flexibility around the panel to prevent damage to the
panel.
The panel might move slightly when it is pushed with a finger, and
clattered sound might be heard. This is not a malfunction.
Overcurrent error message
appears
The connected USB device might cause this error. Remove the device and
turn the TV Off with Mains power On / Off switch, then turn it On again.
Check if foreign objects are inside the USB port.
An error message appears
Follow the message’s instructions.
If the problem persists, contact your local Panasonic dealer or the
authorized Service Centre.
Maintenance
First, remove the mains plug from the socket outlet.
Display panel, Cabinet, Pedestal
Regular care:
Gently wipe the surface of the display panel, cabinet, or pedestal by using a soft cloth to clean the dirt or fingerprints.
For stubborn dirt:
Dampen a soft cloth with clean water or diluted neutral detergent (1 part detergent to 100 parts water). Then wring
the cloth and wipe the surface. Finally, wipe away all the moisture.
Caution
Do not use a hard cloth or rub the surface too hard. This may cause scratches on the surface.
Take care not to subject the TV’s surfaces to water or detergent. A liquid inside the TV could lead to product failure.
Take care not to subject the surfaces to insect repellent, solvent, thinner, or other volatile substances. This may
degrade surface quality or cause peeling of the paint.
The surface of the display panel is specially treated and may be easily damaged. Take care not to tap or scratch
the surface with your fingernail or other hard objects.
Do not allow the cabinet and pedestal to make contact with a rubber or PVC substance for a long time. This may
degrade surface quality.
Mains plug
Wipe the mains plug with a dry cloth at regular intervals. Moisture and dust may lead to fire or electrical shock.
Vista de pagina 92
1 2 ... 88 89 90 91 92 93 94 95 96

Comentarios a estos manuales

Sin comentarios