Panasonic NVGS50B Instrucciones de operaciones descargar pdf (Pagina 54)

Others

-54-

Notes and Hints

ª Concerning the Power Supply

≥When the Movie Camera is used for a long time,

the Camera body becomes warm, but this is not

a malfunction.

≥If the [CHARGE] Lamp does not light up

although the Battery is attached to the AC

Adaptor, detach the Battery and reattach it.

ª Inserting/Removing the Cassette

≥In the case of using a previously recorded

Cassette, you can use the Camera Search

Function to find the position where you want to

continue recording.

≥If a new Cassette is inserted, rewind to the

beginning of the tape before starting recording.

≥When inserting the cassette, make sure it faces

in the right direction and then push it in until it

stops.

≥When the Cassette Holder is in action, do not

touch anything except the [PUSH CLOSE]

Button.

≥When closing the Cassette Compartment

Cover, do not get anything caught in the cover,

such as a cable of an optional stereo

microphone.

ª Alarm Sounds

When [BEEP SOUND] on the

[OTHER FUNCTIONS1] Sub-Menu on the

[CAMERA FUNCTIONS] Main-Menu is set to

[ON], confirmation/alarm beeps are issued as

follows.

1 Beep

≥When you start recording

≥When you switch the [OFF/ON/MODE] Switch

from [OFF] to [ON]

2 Beeps

≥When you pause recording

2 Beeps for 4 times

≥If you perform a wrong operation before or

during recording

ª Recording Check

≥For Recording Check, the recording speed

mode (SP/LP) must be the same as the mode

used for the recording. If different, playback

images will be distorted.

ª Camera Search

≥In Camera Search Mode, images may contain

mosaic-pattern noise. This is a phenomenon

that is characteristic of digital video and not a

malfunction.

≥If the recording speed modes (SP/LP) of

previous recording and new recording are

different, playback images may be distorted.

ª Quick Start

≥During the Quick Start Standby Mode, a minute

amount of electricity is consumed.

≥When the Movie Camera is left in the Recording

Pause Mode for 6 minutes, it will be turned into

the Quick Start Standby Mode. To turn the

Movie Camera on again, set the

[OFF/ON/MODE] Switch to [OFF] and then set it

to [ON] again. (The Quick Start Mode will be

restored.)

≥This Function is not activated in the following

cases even if the Quick Start Recording Lamp

lights:

≥A tape is not inserted, while the Tape Mode

is set.

≥A Card is not inserted, while the Card Mode

is set.

≥In the following cases, Quick Start is temporarily

cancelled when the Quick Start Mode is set. Set

the Camera Mode again, and the Quick Start

Mode will be restored.

≥Set to the VCR Mode or Card Playback

Mode

≥The Battery is replaced

≥If the [QUICK START] Button is pressed and

held for approximately 2 seconds during the

Quick Start Standby Mode, the Lamp will go off

and the Movie Camera will completely be turned

off.

≥If the Movie Camera is not operated for

approximately 30 minutes when the Quick Start

Recording Lamp lights, the Lamp will go off and

the Movie Camera will completely be turned off.

≥In the Automatic White Balance Mode, the

colour may be recorded unnaturally at the

beginning of the recording.

≥The zoom magnification differs from when it is

in the Quick Start Standby Mode and when the

recording starts.

ª Photoshot

≥Photoshot Recording results in slightly inferior

image quality.

50B-ENG.book 54 ページ２００３年１月１７日　金曜日　午後５時２９分

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 75 76

Comentarios a estos manuales

Sin comentarios