Panasonic WV-CS564 Manual de usuario

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WV-C

11 Setup Menu Description● Presetting(1) Position (POSITION SET)Aligns the camera position and focal point by panning, tilting, zooming and focusing.

12● Auto Pan Key (AUTO PAN KEY)This setting assigns the SEQ, SORT, AUTO PAN or PATROL (PLAY) mode to the AUTO key on the con-troller.After setting thi

13● Cleaning (CLEANING)This is used for refreshing the electric-mechanical contacts built in the camera. Use this function formaintenance when the cam

14Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lensiris control in ALC mode.(3) Shutter Speed (

15(6) White Balance (WHITE BAL)You can select one of two modes for white balance adjustment as follows:• Auto-Tracing White Balance (ATW)In this mode,

16SETTING PROCEDURESThe following setting procedures are described on the assumption that this model is used in combinationwith the WJ-SX550B Matrix S

17 Presetting● Preset Menu Display1. Displaying the preset menu directly(1) Move the cursor to PRESET 1 and move the joystick to theright or left to

183. Pan OffsetIf the camera is replaced with a new one, the pan offset functionis used to adjust its positions to be the same as before exceptpatrol

19● Preset Identification Setting (PRESET ID)1. Move the cursor to PRESET ID on the preset setting menu andselect ON or OFF by moving the joystick to

20To Set a Display Position for a Preset ID(1) Move the cursor to POSI and press the CAM (SET) key. Thedisplay position set menu appears.(2) Using the

2The serial number of this product may be found on thetop of the unit.You should note the serial number of this unit in thespace provided and retain t

21● Dwell Time (DWELL TIME)• Move the cursor to DWELL TIME and set a dwell time by movingthe joystick to the right or left. The factory default settin

22 Deleting Preset Positions1. Move the cursor to PRESET 1* and select the position number tobe deleted by using the joystick.2. Press the CAM (SET)

23 Auto Mode Selection (AUTO MODE)1. To set auto modeMove the cursor to AUTO MODE and select a mode by movingthe joystick to the right or left.The fa

245. To set pan limit ON/OFFMove the cursor to PAN LIMIT and select ON or OFF by mov-ing the joystick to the right or left.The factory default setting

25 Auto Pan Key Setting(AUTO PAN KEY)This is used for assigning one of the following auto functions to theAUTO key on the controller. Pressing the AU

** SET UP MENU **PRESET 1 MAP HOME POSITION SELF RETURN AUTO MODE AUTO PAN KEY LOCAL/REMOTE PATROL CLEANINGCAMERARS485 SET UPOFFOFFOFFAUTO PANLOC

27Patrol Learn with a Controller not Having the PATROL Key1. Select the patrol learn in the setup menu, and then close it.Starting points are stored a

28 Cleaning (CLEANING)Built-in electric mechanical contacts are refreshed at regularintervals (approx. 7 days) if CLEANING is set to ON.A dry contra

293. After editing the camera identification characters, follow the stepsbelow to set the position of the CAMERA ID on the monitor screen.3-1 Move the

30● Light Control Setting (ALC/MANUAL)1. Display SET UP on the monitor screen.If necessary, refer to Setup Menu Display on page 16 for detailson displ

31) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this apparatus near water.6) Clea

31(2) ALC Mode with BLC OFF1. Move the cursor to the BLC and select OFF. (When you selectMANUAL, BLC is not available.) The MASK SET appears on themen

32● Shutter Speed Setting (SHUTTER)1. Display SET UP on the monitor screen.If necessary, refer to Setup Menu Display on page 16 for detailson displayi

33● Synchronization (SYNC)1. Display SET UP on the monitor screen.If necessary, refer to Setup Menu Display on page 16 for detailson displaying the SE

347. Use the joystick to match the vertical phases for both video outputsignals as closely as possible. (COARSE adjustment can beincremented in steps

35(2) Automatic White Balance Control Mode (AWC)1. Display SET UP on the monitor screen.(Refer to Setup Menu Display on page 16 for details on display

36● Auto Focus Setting (AF MODE)1. Move the cursor to AF MODE, and select the following mode bymoving the joystick to the right or left.The factory de

37● Electronic Zoom (EL-ZOOM)The electronic zoom magnifies a scene 2-fold. With a 18-fold opticalzoom lens, the camera is capable of 36-fold zoom.1. M

38● Special Menu (SPECIAL)This menu lets you adjust and set up the picture quality to meet yourrequirements.• Display SET UP on the monitor screen.(R

39(5) To Restore the Camera Default Position (REFRESH)Move the cursor to REFRESH by using the joystick and press theF2 button of the WV-CU550B.(For th

40How to Reset to the Factory Preset ParametersAny of the above settings plus the ALC/MANUAL level control and phase adjustments can be reset to thefa

4• High quality picture of 768 x 494 pixels• Minimum illumination of 2 lx (at AGC High)• Protocol adaptability to Panasonic's protocol• A run of

41X ON/X OFF (X ON/X OFF)Specifies whether to apply flow control or not (NOT USE, USE). The factory setting is NOT USE.Wait Time (WAIT TIME)Specifies

43• The following steps of installation and connection should be taken by qualified service personnel orsystem installers and should conform to all lo

44Unit NumberSwitch 1, an 8-bit DIP switch, specifies unit number or returns tothe factory default settings for Panasonic’s protocol.When the switch p

451234ON5678Switch positionUnitnumber1234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON5678123

46Full duplex (4 line) *BP 2BP 1 FunctionSwitchpositionFunctionSwitchpositionRS485 SettingThe 4-bit DIP switch in used forRS485 termination.ONMarking1

475. Tighten the fixing screw M3 (provided).Notes:(1) Tighten the camera fixing screw with ascrewdriver.(2) Follow the instructions given here toensur

48How to Assemble the Cable with theAccessory ConnectorStrip back the cable jacket approx. 3 mm (0.1inch) and separate the individual conductors.Recom

49• RS485 ConnectionNote:Use the cable that is described below for RS485 site communication.• Shielded, twisted pair cable• Low impedance• Wire gauge

50Note: When any peripheral is turned off and turned on again, the camera is also turned off and turnedback on.SYSTEM CONNECTIONS1 2 34 5 67 8 9MON CA

51Zoom ratioBright objectSmearWhen the camera is aimed at a bright light, suchas a spotlight, or a surface that reflects brightlight, smear or bloomin

5 Camera CleaningEven if this function is used, noise may be produced on the monitor screen, or the preset position may bedeviated in the cause of pr

52ControlsAuto focusPanning rangeWeights and dimensions indicated are approximate.Specifications are subject to change without notice.360° endlessposs

53FunctionSelecting a PRESET position From #1 to #32#1 [1] + [CAM FUNC]#10 [1] + [0] + [CAM FUNC]#32 [3] + [2] + [CAM FUNC]AUTO PANON [6] + [5] + [CAM

NM1201-0 V8QA5960AN Printed in JapanN 192001 © Matsushita Communication Industrial Co., Ltd.Panasonic Canada Inc.5770 Ambler Drive, Mississauga,Ontari

64. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera when itis dirty.When the dirt is hard to

7y Camera Mounting Baseu Panning Starting Pointi Fall Prevention Wireo Decoration Cover!0 Dome Coverq Not Usedw Not Usede Video Output Connectorr Data

98SETUPSetupMenuHomePositionSelectionSelfReturnSettingAuto PanKeySettingLocal/RemoteSelectionShutterSpeedSelectionWHITEBALAWC ATWBLCOFFLight Contr

10Open special F2 keyThe keys (switches) to use for setup are shown in the table below. The joystick on the connected con-troller may also be used for