Panasonic AK-MSU930P Manual de usuario descargar pdf (Pagina 8)

Parts and their functions

MONI LINK: Shading link setting

This is used to set whether to link the

monitor when the R, G or B shading

switch has been selected.

ANALOG: CCU analog output setting

This is used to set the analog output of

the CCU to the HD or SD component.

SDI4 OUT: HD SDI4 output selection

This is used to set the HD SDI4 output of

the CCU as the PM or normal output.

SYNC: Sync waveform addition setting

This is used to select whether to add the

sync waveform to the analog output.

TYPE: Analog sync waveform setting

This is used to set the sync waveform to

be added to the HD analog output to

binary or tri-level.

H_CO (HDTV): Horizontal sync signal phase coarse

adjustment

This is used to coarsely adjust the phase

in relation to the HDTV genlock sync

signal.

H_FIN (HDTV): Horizontal sync signal phase fine

adjustment

This is used to finely adjust the phase in

relation to the HDTV genlock sync signal.

H_CO (SDTV): Horizontal sync signal phase coarse

adjustment

This is used to coarsely adjust the phase

in relation to the SDTV genlock sync

signal.

H_FIN (SDTV): Horizontal sync signal phase fine

adjustment

This is used to finely adjust the phase in

relation to the SDTV genlock sync signal.

SCCO: Subcarrier phase coarse adjustment

This is used to coarsely adjust the phase

of the subcarrier signal in relation to the

SDTV genlock sync signal.

SCFIN: Subcarrier phase fine adjustment

This is used to finely adjust the phase of

the subcarrier signal in relation to the

SDTV genlock sync signal.

SH_H: SD/HD horizontal phase

This is used to adjust the horizontal

phase of the SDTV output and HDTV

output.

SH_V: SD/HD vertical phase

This is used to set the vertical phase of

the SDTV output and HDTV output to

line 0 and line 90 (advanced by 90H for

HDTV).

Pedestal control switch [PED CONTROL]

This is selected to adjust the R, G and B pedestal levels

in relation to the master pedestal position.

When it is selected, its lamp lights.

GPED: G pedestal level

Adjustment range: –100 to +100 (amount

of G pedestal offset

from master pedestal)

RPED, BPED: R, B pedestal level

Adjustment range: –100 to +100

The level is increased or decreased from

the level at the pedestal position where

the black balance was attained.

When the black balance is adjusted, 0 is

set as the adjustment value.

Gain control switch [GAIN CONTROL]

This is selected to adjust the white balance. When it is

selected, its lamp lights.

G GAIN: Adjustment range: –100 to +100

(Amount by which the G gain is to be

increased or decreased from its

reference setting)

R GAIN, B GAIN: Adjustment range: –100 to +100

(Amount by which the R or B gain is to

be increased or decreased as

referenced to their levels at the

pedestal position where the white

balance was attained; when the white

balance is adjusted, 0 is set as the

adjustment value.)

Gamma curve control switch [GAMMA CONTROL]

This is selected to adjust the gamma correction.

Since the M GAM adjustment value is independent of the

R and B GAM adjustment values, the R and B GAM

values remain unchanged even when M GAM is

changed.

When the switch is selected, its lamp lights.

M GAM: Master gamma

Adjustment range: 0.600 to 0.300

RGAM, BGAM: Adjustment range: –75 to +75

Flare control switch [FLARE CONTROL]

This is selected to change the amount of flare correction.

When it is selected, its lamp lights.

RFLR, GFLR, BFLR: R, G and B flare

Adjustment range: –50 to +50

(Flare correction operation is

turned off at 0.)

White clip control switch [WHITE CLIP CONTROL]

This is valid when the lamp of the WHT CLIP OFF switch

among the MODE ON/OFF switches is off, and it is

selected to change the white clip level. When it is

selected, its lamp lights.

WHT CLIP: White clip

Adjustment range: 95% to 110%

Knee control switch [KNEE CONTROL]

This is selected to adjust the knee slope and knee point.

MPNT: Master knee point

Adjustment range: 105% to 85%

RPNT, BPNT: R and B knee points

Adjustment range: +10% to –10%

MSLP: Master knee slope

Adjustment range: 63 to 0

RSLP, BSLP: R and B knee slopes

Adjustment range: +32 to –31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Panasonic AK-MSU930P Manual de usuario Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Panasonic AK-MSU930P