Panasonic WV-SF448E Guía de instalación

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number is

10Do not damage the power cable. Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do not place heavy objects. Keep

11About SD memory card • BeforeremovingtheSDmemorycardfromthe camera, it is necessary to select “Not use” for “SD memory card” fi

12Precautions for InstallationPanasonic assumes no responsibility for injuries or property damage resulting from fail-ures arising out of improper ins

13Screw tightening • The screws and bolts must be tightenedwith an appropriate tightening torque according to the material and strength of th

14Major operating controlsAbout the [INITIAL SET] buttonAfter turning off the power of the camera, turn on the power of the camera while holding down

15<Inside view of the sub cover (with sub cover removed)>Network connector12 V DC power supply terminalBuilt-in microphoneExternal I/O terminals

16Camera attachment (accessory)Direction marker for installationCamera attachment position marker

17PreparationsWhen installing the camera, there are 4 methods as specified below.  • Usingthetwo-gangjunctionbox(☞ pages 19) • Installingthe

18Using the side cable access holeWhen installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of the enclosure t

19Method of camera installationUsing a two-gang junction boxSecure the camera attachment (accessory) to the two-gang junction box built in a ceiling o

2The model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this

20Installing the camera directly on the ceiling or wallPlace the installation template label (accessory) on the ceiling or wall, and make a hole to pa

21Using the optional ceiling mount bracket WV-Q105 (E model only)When using the optional ceiling mount bracket to mount the camera, first place the in

22IMPORTANT: • WheninsertinganSDmemorycard,makesurethedirection. • Before removing the SD memory card, select “Not use” for “S

23ConnectionBefore starting the connection, turn off the power of this camera and the devices to be connected. Check and prepare the required devices

24IMPORTANT:•Connect/disconnect the audio cables and turn on the power of the camera after turning off the power of the audio output devices. Other

25v Connecting an External I/O terminal Connect the cables of external devices to the External I/O terminal plug (accessory). q When connecting an

26IMPORTANT: • Donotconnect2wiresormoredirectlytoaterminal.Whenitisnecessarytoconnect2wires or more, split the wire and connect th

27IMPORTANT: • Besuretousethepowercordplugprovidedwiththisproduct. • Besuretofullyinsertthepowercordplug(accessory)intothe

28InstallationCamera mountingMount the camera with the camera attachment (accessary)Installation shall be conducted after turning off each device. zDe

29vUsing the camera attachment position marker as a guide, match the “OPEN” position of the camera to the projection of the camera attachment (accesso

3ContentsImportant safety instructions ... 4Limi

30nTighten the camera fixing screw.IMPORTANT: •Securely tighten the camera fixing screw. Failure to do so may cause damage or thecame

31Configure the network settingsConfiguring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with def

32c Selectthecamerayouwanttoconfigure,andclick[AccessCamera].Note: •When cameras are displayed in [Panasonic IP Setting] screen, click t

33TroubleshootingBefore asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after

34Specifications• BasicPower source: 12 V DC, PoE (IEEE802.3af compliant)Power consumption: 12 V DC*: 610 mA/ 7.3 WPoE 48 V: 140 mA/ 6.7 W (Class 0 de

35ELC(Maximum exposure time):•WithSuperDynamicOnELC (1/30 s)•WithSuperDynamicOffELC (1/30 s), ELC (3/100 s), ELC (3/120 s),ELC (2/100 s), ELC

36• NetworkNetwork: 10BASE-T/100BASE-TX, RJ-45 connectorResolution: 2MPanorama[16:9]/2MDoublePanorama[16:9]:H.264(1)H.264(2)JPEG1920x1080/640x36

37Protocol: IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP, SNMP, DHCPv6, MLD, ICMP, ARPIPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, R

38Standard accessoriesOptional accessoriesInstallation Guide (this document) ... 1 pc.Warranty card (P mod

4Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying docu

5Limitation of liabilityTHIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, TH

6Main functions360° monitoring with a wide variety of transmission modesWith the super-wide-angle fisheye lens, 360° monitoring is possible with a sin

7System requirements for a PCCPU: Intel® CoreTM 2 Duo 2.4 GHz or faster recommendedMemory: 512 MB or more (A minimum of 1 GB memory is required when

8Trademarks and registered trademarksCopyright • Adobe, Acrobat Reader, and Reader are either registered trademarks or trademarks of Adobe Systems I

9PrecautionsRefer installation work to the dealer. Installation work requires technique and experi-ences. Failure to observe this may cause fire, elec