Panasonic WVCU161 Instrucciones de operaciones

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WV-CU161Sy

10Check the DIP switch settings before connecting this controller. They need to be changed only if you want to change the sys-tem settings.The follow

11SYSTEM CONNECTIONThe WV-CU161 can be connected with a camera, a video monitor and a Time Lapse VTR. A typical connection example isshown below. Bas

12 Connection with a Video SwitcherConnected with a video switcher, the WV-CU161 allows you to control multiple combination cameras.WV-CS850 seriesVi

13 RS-485 Site Communication Connection via Codec for CameraDistance of 1 200 m (4 000 ft) or MoreWV-CS850 seriesAV CodecAV CodecRSystem ControllerWV

14 Connection with a Time Lapse VTRConnect the time lapse VTR as shown in the example below.Make sure the polarity of the buzzer matches the terminal

15● Internal Diagram RS-485 TerminalControl data is transmitted and received to and from otherperipherals. Use a data grade, double-shielded, twisted

16SETUP MENUThe Setup menu has four main submenus: Alarm Setup, System Setup, Preset Data Load, and Communication.All of these main menus are further

17WV-CU161 SETUP MENU *.** ALARM SETUP SYSTEM SETUP PRESET DATA LOAD COMMUNICATIONNote: The COMMUNICATION parameter appears when thedata switc

18(1) Alarm Display SettingThis item lets you select whether or not the messageALARM on the monitor when the alarm is activated.1. Display the ALARM S

19 ALARM SETUP ALARM DISPLAY ON SITE ALARM ON TERM.ALARM ON ALARM OUTPUT 10S ALARM BUZZER ON ALARM TERMINAL System Setup1. D

2ENGLISH VERSIONWij verklaren als enige aansprakelijke, dat het product waarop dezeverklaring betrekking heeft, voldoet aan de volgende normen ofander

ERROR 220Message Cause NoteLack of memoryMemory capacity wasexceeded while down-loading.ERROR 3 Causes exceptaboveDownloading not possi-ble for some r

21ERROR1(2) Upload Setting1. Display the PRESET DATA LOAD menu.2. Select a camera number between CAM1 and CAM8 bymoving the joystick up or down.3. Pre

227. After setting all data titles, press the HOME/ESC buttonto return to the Preset Data Menu.To replace a specific character1. Move the cursor to th

23(4) Parity Check SettingThis item lets you set the parity bit for RS-485 communica-tion.1. Display the COMMUNICATION menu.2. Select PARITY CHECK by

24CAMERA CONTROL FUNCTIONSIt is necessary to setup the camera before using the cam-era control functions. For further information, refer to theOperati

25 Operation of Combination CameraIt is necessary to setup the combination camera beforeoperating it. For further setup information, refer to theOper

26● Changing from Colour to Black andWhite PictureThe following function is available with cameras providedwith the colour-black and white switching f

273. To cancel the electronic shutter function, press numericbuttons 1, 7 and 2.4. To increase electronic shutter speed, press numericbuttons 1, 7 and

28 External Device Control● Auxiliary ControlThe following function is available only in cases whereexternal devices are connected to the receiver or

29ALARM CONTROL FUNCTIONSWhen the WV-CU161 receives an alarm signal from a cam-era site, an alarm is activated. The WV-CU161 can handlethe following a

3CONTENTSPREFACE ...

30CAMERA SETUPYou can use the WV-CU161 to setup the camera from theCamera Setup menu.For further information, refer to the Operating Instructionsfor t

31● Camera Patrol Learning for Camera PatrolOperationThe camera patrol learning function can be setup eitherfrom the Camera Setup menu or while operat

32INSTALLATION Mounting in the RackNote: Keep the Power On/Off Switch turned off while mak-ing the following installations.1. Remove the Connector Pa

33The System Controller WV-CU161 can be reset to thedefault settings as follows:1. Turn off the Power Switch.2. Turn on the Power Switch while pressin

34Power Source: 220-240 V AC, 50 HzPower Consumption: 7 WCamera Input: Composite Video Signal: 1 V[p-p]/75 ΩAlarm Input: No-voltage contactAlarm Reco

N0400-1060 YWV8QA5464BN Printed in JapanN 19 Gedruckt in JapanImprimé au JaponImpreso en Japón2000 © Matsushita Communication Industrial Co., Ltd. Al

4PREFACEThe WV-CU161 System Controller is designed for one-to-one use with the Combination Camera such as the WV-CS850 seriesCombination Camera or the

5PRECAUTIONS• Refer all work related to the installation of thisproduct to qualified service personnel or systeminstallers.• Do not block the ventilat

6MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front Viewq Operate Indicator (OPERATE)Lights up while the power of the System Controller isturned on.w

7!1 Preset/Set/Program Preset Button(PRESET/SET/PROGRAM PRESET)PRESET: In combination with the Numeric buttons, thisbutton is used to move a specific

8 Rear ViewPOWEROFFSIGNAL GNDONCAMERAINRS485ALARM DATATERMVIDEOOUTRESET OUTALARM INRECOVER INALARM OUTALARM INLINECOAXRS48542ONOFF12G34RTABABGqwoi !0

9SETUP Data Switch SettingSet this switch to specify the mode of communicationbetween the WV-CU161 and a connected combinationcamera.• Coaxial Multip