Panasonic BT-LH2550 Información técnica

Panasonic Broadcast BT-LH2550 Menu Information

23Main Menu (continued)*5 Remote control via RS-232C ends in error (error response: ER001) when “GPI PRESET1” or “GPI PRESET2”is selected with the GPI

24 16:9 marker(Displayed for HD input and SD input in 16:9 ratiomode.) This marker is only displayed as a vertical bar. The section becomes the “MARK

25 “CROSS HATCH”The “CROSS HATCH” function enables display of markers at regular vertical and horizontal intervals to facilitatecomposition and other

26Underlined values indicate factory defaults.*1 Changes are not reflected to a still image in the main window in the split-screen display of the “TWO

27*2 These functions are not available when “RGB-COMP.” under “YPBPR/RGB” or “DVI-COMP.” under “DVI-D” isselected in the “INPUT SELECT” menu ( page 3

28Main Menu (continued) WB adjustment modeSelect “VAR1” to “VAR3” for “COLOR TEMP.” in the “VIDEO CONFIG” menu to make “WHITE BALANCE VAR1”to “WHITE

29Main Menu (continued)Underlined values indicate factory defaults.*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FA

30 CALIBRATIONThe CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness valuesand internal monitor process

31 CALIBRATIONSelect CALIBRATION in the “SYSTEM CONFIG” menu to open the following menus.*1 “EXECUTING” is displayed during “AUTO CALIBRATION” and “C

32Underlined values indicate factory defaults.*1 Changes in settings change menu settings. FUNCTIONSub menu Settings DescriptionFUNCTION 1 - FUNCTION

15How to Use the On Screen MenuThe screen displays eight types of information: input signal status, picture/volume adjusting menu status,sharpness dis

33 FUNCTION setting restrictionsSettings are not available under the following conditions. Setting Conditions that disable operationHV DELAYIn TWO WI

34Main Menu (continued) Functions displayed during FUNCTION button operationPressing any of the [FUNCTION1] to [FUNCTION5] buttons displays the opera

35Main Menu (continued)“GPI CONTROL” is used to enable and disable GPI functions and assign functions to each of the GPI terminal pins( page 48). Und

36Main Menu (continued)Underlined values indicate factory defaults.*1 All five input lines (VIDEO, SDI1, SDI2, YPBPR/RGB, DVI-D) cannot be turned off.

37 COMP. Set “RGB-COMP” under “YPBPR/RGB” in the “INPUT SELECT” menu and select the “RGB-COMP” input line toenable the “COMP” menu. Underlined values

38Use the following submenus to set headphone output and audio level meters. Underlined values indicate factory defaults.*1 When ANALOG is selected in

39Underlined values indicate factory defaults.*1 Available during HD-SDI input signals.*2 Available during VIDEO (NTSC) input. Closed captions appear

40Main Menu (continued) “WFM/VECTOR” The “WFM/VECTOR” function enables display of the waveform and vector display. Use “DISPLAY SETUP” in themain men

41Main Menu (continued) TWO WINDOW functionThe “TWO WINDOW” function displays two inputs selected from VIDEO, SDI1/2, YPBPR/RGB or DVI-D in twowindow

42Main Menu (continued) TWO WINDOW sizeThe “TWO WINDOW SIZE” setting in the “DISPLAY SETUP” menu determines the size of the main window andsub-window

16• Use the menu to open and set up functions.• When “FUNCTION DISPLAY” ( page 32) is set toON, press any of the "FUNCTION1" to "FUNCT

43Main Menu (continued)• Main window (HD) and sub-window (SD)• Main window (SD) and sub-window (HD)• When the main window and sub-window display video

44Main Menu (continued) TWO WINDOW screen syncIn single screen display, the TWO WINDOW screen is synchronized to the frame rate frequency of the inpu

45Main Menu (continued)Underlined values indicate factory defaults.*1 The menu can be displayed when the lock is engaged. Only “CONTROL/LOCAL ENABLE”

46Main Menu (continued) List of setting restrictions ( : available, ×: not available)*1 This function is not available in the split-screen display o

47Main Menu (continued)*2 This function can be set in the split-screen display of the “TWO WINDOW” function. *5 The VECTOR display appears only during

17• Use the menu to display and set the time code forHD-SDI signal input. It also allows you to switchdisplay mode (VITC, LTC, VUB, LUB).In VITC and L

181. Press [MENU] to display the MAIN menu. 2. Press [ , ] to select a menu and push[ENTER].3. Press [ , ] to select a sub menu and press[ENTER].The

191. Press [ADJUST] to display the picture/volumeadjusting menu.2. Press [ , ] to select item to adjust.The selected item changes to white.3. Press [

20You can save and load up to five combinations of menu settings and picture/volume adjustments as user data. Youcan also return settings and adjustme

21Menu configurationMAIN MENUVIDEO CONFIGSYSTEM CONFIGFUNCTIONINPUT SELECTGPIMARKERGAMMA SELECTCOLOR SPAC E COLOR TEMP.SHARPNESS MODESHARPNESS HSHARPN

22This function is not available in split screen display of the TWO WINDOW function. (CROSS HATCH is notaffected.)Underlined values indicate factory d