Panasonic KX-PNB2 Manual de usuario

PanasonicNetwork Card for EthernetQuick Installation GuideModel No. KX-PNB2This guide is intended only to cover the gertoral steps in connecting your

8 a) Gently tighten the two screws. b)Close the rear cover.Rear coverQ Replace the 1st cassette, then reconnect any interface cables and power cord.1

Selecting the Network Print MethodThere are two ways of network printing. You may need to contact your network administrator to select it.• Printing

Printing through the shared computer (server)A print job of a computer (client) is transferred to the Network Card (printer) by the shared computer (s

Printing Directly from a ComputerThe network printing is configured in the following outline order.Step 1 Setting up the TCP/IP protocol on the Networ

step 1: Setting up the TCP/IP protocol on the Network CardThe setting up of IP address, Subnet Mask and Default Gateway are required for the Network C

I Make sure “READY” appears on the printer’s operator panel display.2 Press ON LINE/CONTINUE button.3 Press MENU O button until “NETWORK MENU” appear

9 if “YES" appears, press VALUE O button, then ENTER/CANCELbutton.10 Press ITEM O button.11 \f “NO” appears, press VALUE O button, then ENTER/CAN

15 Repeat steps 12 to 14 three times to finish entering value of the IP address.16 Press ENTER/CANCEL button.17 Press ITEM 6 button.SM BYTE1 0 X18 E

21 Press ENTER/CANCEL button.SM BYTE4 XXX t22 Press ITEM 6 button.GW BYTE10 %23 Enter the leading 3 digits of the Default Gateway. (To decide the val

I step 2: Setting up the TCP/IP protocol on the computerTo use IP Peer-to-Peer printing directly from the computer, the TCP/IP protocol must be instal

Thank you for purchasing the Panasonic Network Card for Ethernet, KX-PNB2.This Network Card for Ethernet (hereafter Network Card) KX-PNB2 is designed

Step 3: Installing and setting up IP Peer-to-Peer printer port on the computer Installing the printer driverIf the printer driver has not been instal

Setting up IP Peer-to-Peer printer port<When the computer is Windows 95A/Vindows 98>The following windows are for Windows 98.231 Click rstart]

5 Click I Add Port... I.Select the t^pe o( port you vttri to acid0||NetwOTySpecilv the nelMOik path to the prhtet;Erowte.,;i O Q'hetI CBck the t&

<When the computer is Windows NT 4.0> 1234Click Start I, select Settings, and click Printers.Click the printer with the Network Card installed a

6 Click KX-PNB2 Network Printer Port from the [Available PrinterPorts:], and click New Port...Prrtaf ^Janv!> i}KXP000a0aM7cdI I IP AdAe»i?ntef Pof

Printing through the Shared Computer (Server)The network printing is configured in the following outline order.Perform steps 1 to 3 in the “Printing D

Step 4: Sharing the printer port on the serverNote• If the Sharing tab does not appear during the setup, click Network Computer and in the Properties

6 a) If you do not enter the password, click |OKb) If you enter the password, perform the following step.mPassword ConfirmationPlease reenter your pas

If using the separator page on the server (Windows NT 4.0), proceed to step 5 below. If not, proceed to step 6 on page 29.Step 5: Setting up the sep

7 Select pci.sep, then click I OpenIf the PS SIMM is installed in your printer, select pscript.sep.89Click OKClick OK to close the printer properties

ContentsBefore You StartFeatures...-...4Instructions on the CD-ROM...

T Click I Browsed.r|.& Double-click the server to display the printer and select the printer. 9 Click OK three times.<When client is Windows N

By Using the Network Setup ToolNote• To install the Network Setup Tool, see “ Installing IP Peer-to-Peer printer port” on page 20.Click Start I, selec

FOR USERS IN UNITED STATESTechnical Support CallsIf you have read this manual and tried the troubleshooting procedures and you are still

Features_______________________________________• Supports 100Base-TX and lOBase-T• Supports the following operating systems- Windows® 95*^/Windows

UnpackingIf you purchased the Network Card as an option, make sure that the following items are included. Report damage or shortages to the reseller f

To remove the printer coverSee the “IMPORTANT’ on page 5.1 Turn the printer OFF and pull out the 1st cassette.1 St cassette2 Unplug the power cord a

5 a) Rotate the printer cover away from the printer. b)Lift the printer cover away.Printer cover6 Remove the five screws from the metal plate coveri

2, Remove the plate. PlateInsert the connector on the Network Card into the network card connector on the printer control board until it is completel

To install the printer covera) Replace the top screw loosely and hang the plate on it.b) Tighten the other four screws.c) Tighten the top screw.6 Sta