Panasonic WVNP472 Manual de usuario

(Lens : option)SDIIday/nightBefore attempting to connect or operate this product,please read these instructions carefully and save this manual for fut

• Connection to Intranet (Type 2)• Connection to Internet (Type 3)• Connection to Internet (Type 4)-10-ALARM INALARM OUTAUX OUTDAY/NIGHT INGNDABVIDEO

-11-OPERATING THE CAMERAYou can operate the camera in two ways: from the PCby way of network, or locally from the camera or systemdevice. Access from

• Function Comparison / PC Network vs. Camera site-12-4. Set the following parameters.Note: Ask your system administrator about param-eters if you are

-13-PRIOR TO SET UPThis section describes setup procedures common toaccesses from the PC and from the camera. The PCcan control more functions than ca

-14-7. Move the cursor to CAMERA O, and click theENTER button. CAM SET UP opens. Notes: • Refer to the next page for setup operations.• Return the men

-15-The following pages describe setting operations from the camera. For accessing from the PC, interpret these instructions as follows.SETTING PROCED

-16-To edit the CAMERA ID1. Move the cursor to CAMERA ID.The factory default setting is OFF.2. Press I. The CAMERA ID menu appears. Thecursor on the

-17-2-2. ALC Mode with SUPER-D2 OFF and ELCModeNote: If ELC is selected, set MASK SET according tothis procedure.1. Move the cursor to SUPER-D2 and se

-18-5. Electronic Sensitivity Enhancement (SENS UP)There are two modes for SENS UP.AUTO: If you select X10 AUTO, for example, thesensitivity is automa

-19-Manual Fine Adjustment for AWC (ATW)You can set the white balance items manually.1. To set MASK SET, proceed as described in steps 2to 4 of “ALC m

-2-WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposedto dripping

-20-10. Special MenuThis menu lets you adjust and set up the video signal ofthe camera to meet your requirements.Move the cursor to RET in the bottom

-21-To reset to the factory settings (CAMERA RESET)1. Move the cursor to CAMERA RESET. PUSH SW ishighlighted.2. While holding down L and M, hold down

-22-SET UP FROM THE PCPREPARATIONS FOR THE PC ConnectionsPrior to connections, specify the connection type andprepare relevant devices and cables.Not

-23- Network Setup of the PCTo set up the network of the PC, first change the TCP/IPsettings of the PC to match them to the default settingsof the ca

-24-6. Click “Internet Protocol (TCP/IP)”, and then clickthe [Properties] button.7. Click the “Use the following IP address” radio but-ton and enter t

-25-3. Click the Setup Menu button. The User authentica-tion dialog appears.• Enter “admin” in the user name column.• Click the OK button. Network Se

-26-Connection type 2 IP address Set the IP address designated by your network administrator.However, the setting is not required if DHCP is used in a

-27-Secondary server Set the IP address of DNS when using the DNS server.Refer to your internet Internet service provider for the IPaddress of the DNS

-28-Host name Refer to your Internet service provider and set the designatedhost name if required.DNS Set to ON when using the DNS server.Primary serv

-29-CAMERA SET UP FROM THE PCThe camera setup menus overlaid on the camera pic-ture appear by clicking the Camera Setup button in themain page. You wi

-3-CONTENTSPREFACE ... 4Features ...

-30- Camera Setup MenusMenu windows are shown in this page. Refer to page15 for menu operations.

-31-Setup windows listed below are accessible only fromthe PC. Operations in these windows are described inthe following pages.Click any of the setup

-32-1. Open the Alarm Setup window.2. External Alarm• Select ON or OFF, and click the SET button.ON: Receives alarm inputs via the ALARM INterminal.OF

-33-2. Common Setup• Enter the FTP server address.A hostname.domainname can be enteredwhen using the DNS function.• Enter the user name with a maximum

-34- Host SetupNote: Never turn over the order: start with the host reg-istration, and then proceed to the authenticationON/OFF.1. Open the Host Setu

-35-You can reset the following data back to the factorydefault settings.Camera SetupSetup Menu (PC oriented)HTML files Initializing the Camera Menu•

-36-VIEWING PICTURES Image Quality Selection1. Click the Setup Menu button in the main page.The Network Setup window opens.2. Click the Image button

-37- Monochrome ModeYou can switch the camera between the colour modeand black-and-white mode. This may help picturebecome clear under conditions of

-38-When an alarm sounds, the camera performs outputfunctions depending on the setup.Inputs: • The alarm sensor connected to the ALARM IN ter-minal on

-39- Canceling Alarm Display“Alarm” display in the upper right corner will disappearwhen you operate the following.• Click the Return button after on

-4-Features• 10/100BASE-T terminal enables your PC to viewcamera images via the network.• SD II (super dynamic) system allows a wide rangeof 46 dB whi

-40-Transparency: Indicates a non-masked area thathas been incorporated into the detection area.Blink: Indicates a non-masked area when the cur-sor is

-41-3. The selected picture is displayed, and the alarmimage control panel appears on the bottom of thescreen. The title of the control panel is follo

-42-AUXILIARY OUTPUT CONTROL Auxiliary Output ControlYou can turn on or off the connected device, for exam-ple a lamp that is connected to the AUX OU

SymptomNo picture is displayed.-43-TROUBLESHOOTINGHTML documents are not displayed.• Is the AC adapter firmly plugged in to the outlet?• Are the POWER

-44-SPECIFICATIONSGeneralAmbient Operating Temperature: –10 °C - +50 °C (14 °F - 122 °F)Ambient Operating Humidity: Less than 90 %Power Source and Pow

-45-STANDARD ACCESSORIESBody Cap ... 1 pc.ALC Lens Connector (YFE4191J100)

Matsushita Electric Industrial Co., Ltd.Web Site : http://www.panasonic.co.jp/global/2003 © Matsushita Electric Industrial Co., Ltd. All rights reser

-5-1. The installation should be made by qualifiedservice personnel or system installers.2. Do not attempt to disassemble the camera.To prevent electr

tiyouq w erWV–NP472ALARM INALARM OUTAUX OUTDAY/NIGHT INGNDABVIDEO OUTRCVLINK10BASE-T/100BASE-TXPOWERDC 12VIN!3!4!2!1!0-6-MAJOR OPERATING CONTROLS AND

-7-• Mounting the LensNotes:• Using the lens having improper protrusion willdamage the camera. The protrusion of the lens intothe camera body should b

-8-• Flange-back AdjustmentThe adjustment is required only when a lens withoutfocus-adjusting mechanism is mounted, or when a lenswith adjusting mecha

-9-Power-in ConnectionsNotes:• Use only a class-2 power supply suitable to thevoltage and current required by the camera. Seespecifications.• Use a UL