Panasonic AW-RP50N Manual de usuario

3TR006602BAAOperating Instructions<Operations and Settings>Remote Camera ControllerModel No. AW-RP50N

10Selecting the settings for a selected remote cameraAutomatically adjusting the white balanceSet the automatic adjustment if the coloring appears unn

11Selecting the settings for a selected remote cameraManually adjusting the white balance( Setting the R and B gain values)1 As with the automatic ad

12Selecting the settings for a selected remote camera Setting the black balanceThe black balance must be adjusted when using a remote camera for the

13Selecting the settings for a selected remote camera Setting the shutter speedThe shutter mode and shutter speed of the remote camera can be select

14Selecting the settings for a selected remote camera Setting the shooting modeSelect the shooting mode that matches the shooting conditions.Select

15 Operating the menu items of the selected remote cameraThe menu operations of the remote cameras can be operated from the unit for the remote camera

16 Setting the USER buttonsMenu items can be assigned to the two USER buttons (USER1, USER2).The target function can be activated simply by pressing t

17 Tally settingsSet enable (On) or disable (Off) for tally ON which provides the tally instructions to the remote camera in response to tally request

18 Setting the functionsThis section describes how the unit’s functions are set.The following functions can be set. Setting of the remote camera ope

19Setting the functions Setting the remote camera operationsSet these operations by selecting the [SETUP] menu followed by the [OPERATE] menu.[4]OPE

2ContentsBefore use ... 3Overview ...

20Setting the functionsSettings when the remote camera moves horizontally or vertically during tele shootingDuring tele shooting, the remote camera’

21Setting the functions Setting the speed at which to move to the position set by the preset memoryThe speed at which to move to the position where

22Setting the functions Setting the movement range of the remote camera (limiter function)This unit has a limiter function which is a function that

23Setting the functionsSetting the left limitFrom the [SETUP] menu, select [PTZ ADJ] and display [LIMIT LEFT]. Then set the left limit.The setting t

24Setting the functions Controlling the peripheral devices connected to the remote camerasWhen any of the peripheral devices listed below are connec

25Setting the functions Adjusting the minimum lens zoom start speedThis adjustment ensures that the lens zoom will start moving smoothly in line wit

26Setting the functions Locking the button operationsThis disables the operation of the CAMERA OSD button and PRESET MEMORY/MENU buttons (1 to 7).Th

27 Setting linkup with the switcherThis setting is used to link the unit with an optional switcher (AW-HS50).To link the unit with the switcher, the f

28Setting linkup with the switcher Link setting1 Set the MENU button to ON.Press the MENU button to light its indicator.2 Set PRESET MEMORY/MENU 9

29 Setting the functions when the unit is linked with the switcherSet the various functions to be used when the unit is linked with the switcher. Se

3 Before use OverviewThis unit is a controller which is designed to control remote cameras (cameras integrated with pan-tilt heads) and pan-tilt hea

30Setting the functions when the unit is linked with the switcher Switcher settingsA setting for controlling the switcher linked with the unit is av

31Setting the functions when the unit is linked with the switcherBus settingFrom the [SETUP] menu, select [SW LINK] and display [BUS]. Then set the ma

32Setting the functions when the unit is linked with the switcherOA tally settingFrom the [SETUP] menu, select [SW LINK] and display [TALLY_IP]. Then

33Setting the functions when the unit is linked with the switcher Setting for the information to be displayed on the OSDThis setting displays the re

34Setting the functions when the unit is linked with the switcherSetting each information item to be displayedVideo formatFrom the [SETUP] menu, sel

35 Checking the equipment alarm informationIt is possible to check the alarm statuses of the unit and the remote cameras assigned to the CAMERA STATUS

36 Returning the unit to its factory statusThe unit’s settings can be returned to the factory statuses.Two methods can be used: One method returns all

37 Control interface for external devices TALLY/GPITALLY IN 1 to TALLY IN 5 are contact input ports which are used to light the unit’s tally indicat

38 Setup SoftwareThe “Setup Software” is an application which enables the same functions as the unit’s automatic IP settings to be executed from the h

39Setup SoftwareDisplaying the “Setting” tab           List boxThe IP address of the AW-RP50 connected to the network is displayed her

4 How to turn the power of the remote cameras on and offHow to turn the power of the remote cameras onFollow one of the procedures below to turn on

40Setup SoftwareAuto IP settingWhen IP addresses are to be changed1 Click [RENEW].New IP addresses are set in the target remote cameras and switche

41Setup Software Saving and loading dataOn the “File Operate” tab screen, the files with the network environment settings are saved and loaded.Sav

42Setup Software Referencing the network environmentOn the “IP Address” tab, it is possible to select the IP addresses of the other AW-RP50 remote c

43 Table of menu itemsButton Menu item Control device Initial value Setting1 GAIN/PED GAIN AW-HE50 Auto, 0dB, 3dB, 6dB, 9dB, 12dB, 15dB, 18dBAW-HE100

44Button Menu item Control device Initial value Setting5 SHUTTER SHUTTER AW-HE50 Off, Step, SynchroAW-HE100 Off, Step, SynchroAW-HE870 Off, Step, Sync

45Button Menu item Control device Initial value Setting9 SETUP [1]USER 1.USER1 AWB SWLINK, BUSCONT, FASIST, CAMSEL, TALLY_IP, CAMINF, AWB, ABB, POWER

46Button Menu item Control device Initial value Setting9 SETUP [6]FUNCTION 1.ND FILTER AW-HE50 “–––”AW-HE100 “–––”AW-HE870 Off, OnAW-E860, AW-E750, AW

47Button Menu item Control device Initial value Setting10 SYSTEM [1]CAMERA CTL 1.CAM1 to100.CAM100NoAsign Serial, Network, NoAsign[2]CAM ASSIGN 1.CA

F0610Y1070 D© Panasonic System Networks Co., Ltd. 2010

5 How to turn the power of the remote cameras on and offHow to turn the power of the remote cameras offFollow one of the procedures below to turn of

6 Setting and operating the preset memoriesThis unit is provided with a function for registering the positions to be shot by the remote cameras and th

7Setting and operating the preset memories Executing the preset data1 Press one of the CAMERA STATUS/SELECTION buttons 1 to 5 to select the remote

8 Selecting the settings for a selected remote cameraThe following settings and adjustments can be performed for a selected remote camera directly fro

9Selecting the settings for a selected remote camera Setting the white balanceThe ratio between RGB (three primary colors) is adjusted so that white